Hummel HSK-M nickel-plated brass metric cable glands crossed to AGRO Progress MS. Both lines are nickel-plated brass, metric thread, rated IP 68 (10 bar) and IP 69, and run from -40 C to +100 C. The AGRO parts come from the Aeros USA line that Applied Control represents in Michigan and Indiana. Hummel sells two or three clamping ranges in each thread size. AGRO covers each thread with one two-piece insert, so cross by thread first and then read the fit column. Every AGRO part number links to its product page and datasheet.
Request a Quick QuoteBook a Time to Review the Application
Hummel HSK-M to AGRO Progress MS, M16 to M63
| Hummel part | Thread | Hummel clamping range | AGRO short thread | AGRO long thread | AGRO clamping range | Fit | Wrench, Hummel / AGRO | Thread length mm, Hummel / AGRO |
|---|---|---|---|---|---|---|---|---|
| 1.609.1600.51 | M16x1.5 | 2 to 6 mm | 1000.17 | 1100.17 | 6 to 10.5 mm | Cable must be 6 mm or larger | 17/19 / 18 mm | 6 / 5 short, 10 long |
| 1.609.1600.50 | M16x1.5 | 4 to 8 mm | 1000.17 | 1100.17 | 6 to 10.5 mm | Cable must be 6 mm or larger | 17/19 / 18 mm | 6 / 5 short, 10 long |
| 1.609.1611.50 | M16x1.5 | 5 to 10 mm | 1000.17 | 1100.17 | 6 to 10.5 mm | Cable must be 6 mm or larger | 20 / 18 mm | 6 / 5 short, 10 long |
| 1.609.2000.51 | M20x1.5 | 5 to 9 mm | 1000.20 | 1100.20 | 8 to 15 mm | Cable must be 8 mm or larger | 22 / 24 mm | 6 / 6 short, 10 long |
| 1.609.2000.50 | M20x1.5 | 6 to 12 mm | 1000.20 | 1100.20 | 8 to 15 mm | Cable must be 8 mm or larger | 22 / 24 mm | 6 / 6 short, 10 long |
| 1.609.2016.50 | M20x1.5 | 10 to 14 mm | 1000.20 | 1100.20 | 8 to 15 mm | Full range covered | 24 / 24 mm | 6 / 6 short, 10 long |
| 1.609.2500.51 | M25x1.5 | 9 to 16 mm | 1000.25 | 1100.25 | 12.5 to 20.5 mm | Cable must be 12.5 mm or larger | 30 / 30 mm | 7 / 7 short, 11 long |
| 1.609.2500.50 | M25x1.5 | 13 to 18 mm | 1000.25 | 1100.25 | 12.5 to 20.5 mm | Full range covered | 30 / 30 mm | 7 / 7 short, 11 long |
| 1.609.3200.51 | M32x1.5 | 13 to 20 mm | 1000.32 | 1100.32 | 17 to 25.5 mm | Cable must be 17 mm or larger | 40 / 36 mm | 8 / 8 short, 13 long |
| 1.609.3200.52 | M32x1.5 | 15 to 21 mm | 1000.32 | 1100.32 | 17 to 25.5 mm | Cable must be 17 mm or larger | 36 / 36 mm | 8 / 8 short, 13 long |
| 1.609.3200.50 | M32x1.5 | 18 to 25 mm | 1000.32 | 1100.32 | 17 to 25.5 mm | Full range covered | 40 / 36 mm | 8 / 8 short, 13 long |
| 1.609.4000.52 | M40x1.5 | 19 to 27 mm | 1000.40 | 1100.40 | 24 to 33 mm | Cable must be 24 mm or larger | 46 / 46 mm | 8 / 8 short, 13 long |
| 1.609.4000.51 | M40x1.5 | 20 to 26 mm | 1000.40 | 1100.40 | 24 to 33 mm | Cable must be 24 mm or larger | 50 / 46 mm | 8 / 8 short, 13 long |
| 1.609.4000.50 | M40x1.5 | 22 to 32 mm | 1000.40 | 1100.40 | 24 to 33 mm | Cable must be 24 mm or larger | 50 / 46 mm | 8 / 8 short, 13 long |
| 1.609.5000.51 | M50x1.5 | 25 to 31 mm | 1000.50 | 1100.50 | 33 to 42 mm | Below the AGRO range, step down one thread | 57 / 55 mm | 9 / 9 short, 14 long |
| 1.609.5000.50 | M50x1.5 | 32 to 38 mm | 1000.50 | 1100.50 | 33 to 42 mm | Cable must be 33 mm or larger | 57 / 55 mm | 9 / 9 short, 14 long |
| 1.609.6300.51 | M63x1.5 | 29 to 35 mm | 1000.63 | 1100.63 | 40 to 52 mm | Below the AGRO range, step down one thread | 64/68 / 70 mm | 10 / 10 short, 14 long |
| 1.609.6300.50 | M63x1.5 | 37 to 44 mm | 1000.63 | 1100.63 | 40 to 52 mm | Cable must be 40 mm or larger | 64/68 / 70 mm | 10 / 10 short, 14 long |
Hummel data from the HUMMEL cable gland catalogue and hummel.com product pages. AGRO data from the AGRO product datasheets. Confirm both against the current datasheet before you order.
Where the two differ
Clamping range. Hummel splits each thread into small, standard and large cable inserts. AGRO's two-piece insert covers the standard and large Hummel ranges in one part number. The small-cable Hummel parts (the .51 numbers, and 1.609.4000.52) start below the AGRO range for that thread. For those, step down one AGRO thread size and use a reducer, or confirm the cable meets the AGRO minimum in the fit column.
Sealing insert. HSK-M uses a splined polyamide clamping insert with an NBR seal and NBR O-ring. Progress MS uses a two-piece insert with a removable inlet, TPE and NBR seal, NBR O-ring.
Thread length. HSK-M standard runs 6 to 10 mm and matches the AGRO short thread 1000 series within 1 mm at every size. The Hummel elongated thread (.30 and .31 numbers, 10 to 15 mm) matches the AGRO long thread 1100 series.
Wrench size. The table lists both. The gap is up to 4 mm at M32 (Hummel 40, AGRO 36) and M40 (Hummel 50, AGRO 46). AGRO is 2 mm smaller at M50 and 2 mm larger at M63. Check clearance between glands on a tight entry plate.
Type rating. Hummel lists NEMA 4, 4X and 6 on the HSK-M. The AGRO 1000.20 datasheet lists NEMA Type 4X. If the panel spec calls for a Type 6 gland, ask and we pull the UL file for the AGRO size.
Shielded cable
For a shielded VFD or servo cable, cross the Hummel HSK-M-EMV to the AGRO Progress EMC easyCONNECT gland in the same thread: 1083.17 (M16), 1083.20 (M20), 1083.25 (M25), 1083.32 (M32), 1083.40 (M40), 1083.50 (M50). Pair it with Tekima 365S VFD cable and send both for one quote.
Common questions
Is an AGRO Progress MS gland a direct replacement for a Hummel HSK-M?
By thread and rating, yes. Both are nickel-plated brass metric glands rated IP 68 at 10 bar and IP 69 from -40 C to +100 C. By cable, check the clamping range. Hummel offers two or three clamping inserts per thread size and AGRO covers the size with one two-piece insert, so the small-cable Hummel variants may need the next smaller AGRO thread.
Which Hummel part numbers are on this page?
The HSK-M metric standard thread series, 1.609.xxxx.50, .51 and .52. The elongated thread versions ending in .30 and .31 cross to the same AGRO sizes; use the AGRO long thread 1100 series for those.
Do you cross Hummel HSK-M-EMV and HSK-M-Ex glands?
Yes. HSK-M-EMV glands for shielded cable cross to the AGRO Progress EMC easyCONNECT series. HSK-M-Ex glands cross to the AGRO Progress MS EX series, quoted on request with the zone and the certificate you need.
Do you cross the plastic HSK-K glands?
Yes. HSK-K polyamide glands cross to AGRO Syntec and Progress GFK polyamide glands. Send the part number and the cable outside diameter.
Cross a Hummel part number now
Send the Hummel part number, the cable outside diameter and the quantity. Pick a quick quote, or book a time to review the application.
Request a Quick QuoteBook a Time to Review the Application
More cross references
More cable gland crosses: Lapp SKINTOP MS-M to AGRO. Pflitsch, Jacob and Thomas and Betts glands cross the same way; send the part number. All AGRO glands are on the Aeros USA collection page.
Other families: VFD cable, Hoffman to Hammond enclosures, enclosure air conditioners, control transformers, line reactors, Class J fuse holders. See every cross on the cross reference index.
HUMMEL and HSK are trademarks of HUMMEL AG. AGRO and Progress are trademarks of AGRO AG. Lapp, SKINTOP, Pflitsch, Jacob and Thomas and Betts are trademarks of their respective owners. Competitor brand names and part numbers appear on this page solely to identify products for comparison. Applied Control Inc. is not affiliated with, endorsed by, or sponsored by any competitor named. Specifications are taken from publicly available manufacturer documentation and are subject to change. Verify current specifications against the manufacturer's own datasheet before purchase or installation.