Belden's composite VFD cables cross to the Tekima 365S 1xG + 1xP series. These are VFD motor supply cables with a shielded signal pair built into the same jacket for a brake, thermistor or temperature sensor.
Email a Part Number for a QuoteCall 248-425-9065
Cross reference
| Belden | Size | Tekima equivalent | UL listing |
|---|---|---|---|
| Belden 29511 | 14 AWG + 16 AWG pair | Tekima CVFM0104_0365S | UL Listed TC-ER |
| Belden 29512 | 12 AWG + 16 AWG pair | Tekima CVFM0106_0365S | UL Listed TC-ER |
| Belden 29513 | 10 AWG + 16 AWG pair | Tekima CVFM0109_0365S | UL Listed TC-ER |
Add the jacket color code to order: _GR for gray, _NE for black.
Signal pair options
Tekima builds more pair combinations than the Belden range covers. At 12 AWG power you can specify an 18, 16 or 14 AWG signal pair. At 10 AWG power the same three options apply. If your sensor circuit needs a heavier pair than the competitor part offers, that is a spec you can win on rather than compromise on.
Two signal pairs
Tekima also builds a 1xG + 2xP construction with two independently shielded pairs under one jacket. Same UL Listed TC-ER approval. Useful where a brake and a thermistor both need to run back to the panel.
Check the UL listing before you substitute
Tekima builds two low-capacitance VFD families and they are not interchangeable.
- 365S is UL Listed Type TC-ER (file E361258), XHHW-2, 600/1000V, direct burial, sunlight resistant, oil resistant I and II, FT4/IEEE 1202, WTTC, c(UL) CIC/TC-ER, and MTW 600V. This is the series that substitutes for competitor tray cable.
- 361S is c(UR)us Recognized under AWM Style 2570 (file E314444) and carries an 80°C rating at 1000V on the UL side. It is not tray cable. Use it inside enclosures and machinery per NFPA 79 and UL 508A, not in an exposed tray run.
Every cross on this page is to 365S. If a quote comes back referencing 361S for a tray application, it is the wrong part.
Common questions
What is the equivalent of Belden 29511, 29512 and 29513?
Belden 29511 crosses to Tekima CVFM0104_0365S, Belden 29512 crosses to CVFM0106_0365S, and Belden 29513 crosses to CVFM0109_0365S. All three are VFD motor supply cables with an integral shielded signal pair for a brake, thermistor or temperature sensor.
Why use a VFD cable with a built in signal pair?
It puts the brake or temperature sensor conductors inside the same jacket as the power conductors, with its own shield. That removes a second cable pull, a second gland, and a second tray fill calculation. The separate shield keeps drive noise off the sensor circuit.
Does Tekima offer a VFD cable with two signal pairs?
Yes. Tekima builds a 1xG + 2xP version of the 365S with two independent shielded pairs, carrying the same UL Listed TC-ER approval as the single pair version.
Get a cross-referenced quote
Send the part number and the footage. We come back with the Tekima equivalent, the construction difference if there is one, and a price inside 48 hours.
Email a Part Number for a QuoteCall 248-425-9065
Tekima also runs a UL certified cut-to-length service. If you are buying full reels and scrapping the offcuts, tell us the cut list and we will quote it cut to size.
Email: christian.lauderback@appliedcontrolinc.com
Phone: 248-425-9065
Belden® is a registered trademark of Belden Inc. ÖLFLEX® and SKINTOP® are registered trademarks of Lapp Holding SE. Southwire® is a registered trademark of Southwire Company, LLC. HELUKABEL®, TOPFLEX® and TOPSERV® are registered trademarks of HELUKABEL GmbH. SABIX® is a registered trademark of SAB Bröckskes GmbH & Co. KG. Applied Control Inc. is not affiliated with, endorsed by, or sponsored by any of these companies. Competitor part numbers appear here solely to identify products for comparison. All specifications are taken from publicly available manufacturer documentation and are subject to change. Verify current specifications against the manufacturer’s own datasheet before purchase or installation.